Meibang Environmental Protection Equipment Co.,Ltd.
Specializing in the production of belt filter presses for sludge and plant residue dewatering
Meibang Environmental Protection Equipment Co.,Ltd. Specializing in Belt Filter Press for Sludge and Plant Residue
skype : marszhangjian@163.com whatsapp:+86 13926239002
×

Send Message

If you have any queries about prices or cooperation, please feel free to e-mail in the E - mail us or use the following inquiry form.

  • Name

  • Email

  • Tel

  • Country

  • Message

  • Captcha

How to maintain belt filter machine ,belt sludge filter dewatering and sludge filter machine ?

Date:2018-10-24 18:46:44

General rules of maintaining belt filter machine and belt sludge filter dewatering

 

1.Belt filter machine  and belt sludge filter dewatering must be designated by a person to use and maintain

2.Before starting the filter press in each shift, the operator carefully checks the lubrication conditions of the lubrication points and the fastening conditions of the parts to ensure that the whole machine is well lubricated and clean and tidy.

3. All parts with speed regulating devices, Speed at zero or low speed when starting, turn off to zero or low speed; mechanical speed regulator is not allowed to adjust at shutdown.

4. Careful protection of motor and electrical equipment, Do not allow sludge or water into the motor and control box.

5. To avoid accidents,not allow to place any tools on Filter belt and in the machine

 

 5安徽宿州河道泥浆脱水.jpg

 

Daily maintain for belt filter machine and belt sludge filter dewatering and sludge filter machine

1.When the filter press starts, the operator will stick to his post ,pay attention to the working condition of the filter press at any time, whether there is abnormal noise or smell: whether there is any debris entering the sludge pump or filter press; whether the filter cloth cleanness is normal,

2.Check the water level in the air compressor gas water separator and the oil level in the oil mist separator on each shift, release water and add lubricating oil in the condition of no pressure if necessary.

3.After each shift work, Operator:

4.Wash the compressor (including all accessories) inside and outside, ensure filter cloth clean, inside and outside clean, clean site, ensure no mud, dirt.

5.Use wooden scraper to clean the scraper plate, And clean down.

6. Scrubbing the flocculant and medicine tools.

20161031_IMG_2550.jpg

Weekly maintain for belt filter machine and belt sludge filter dewatering and sludge filter machine

1.Sludge metering pump, flocculant metering pump, filtrate pump part:

2.Check sludge metering pump, flocculant metering pump and driving part, To solve the abnormal condition of leakage (mud) and drive device.

3.Check the effluent and leakage of filtrate pump.

4.Wash the equipment of mixing and dilution of flocculant; clean the diffuser of flocculant (if used).

 

Air compressor part:

1.Check the oil level , add sufficient if insufficient.

2.Discharge condensate from gas tank.

3.Clean air filter.

4.Manual check the function of air compressor valve.

 

How to maintain belt filter machine ,belt sludge filter dewatering and sludge filter machine ?

  1. All rolling bearings are filled with calcium or lithium grease;

  2. Drive gear with calcium base grease;

  3. Guide roller slide, Lubricating grease.

  4. Bracket for belt guide and tensioning cylinder and lubricating oil for U ring pin.

  5. Check filtrate box and bottom tank in drain and pressure zone, Wash the deposited sludge.

  6. Check the rubber water seal on each rotating shaft and reset if necessary.

  7. Check the belts status

     钾长石泥浆脱水后效果.jpg

    Monthly  maintain for  belt  filter machine  and belt sludge filter dewatering and sludge filter machine
    1. All driving motors are inspected ,mostly temperature rise and sound

    To the control box for a full-system functional inspection.

     

    Quarterly maintain for belt  filter machine ,belt sludge filter dewatering and sludge filter machine
    1. Check the production capacity of air compressor.

    2. bearings of Belt conveyor roller be added lubricating oil.

    微信图片_20180720162819.jpg

    Yearly Maintain for belt filter press, sludge dewatering belt filter press, sludge filter press

    Replacement of air compressor oil.

    2.Replacement of motor gear box oil.

    Check filtrate pump rotary bearings, Refill grease.

    4.Check all bearings of filter press, replace grease.

     

    The moisture content of the filter cake is about 20-65% by Ambang environmental belt filter press, sludge dewatering belt filter press and sludge filter press. The sludge after dewatering can be dried or packed and transported. Filtered clean water can be recycled or discharged naturally.

     

    We have professional equipment manufacturers,  with more advanced mechanical processing equipment and experimental equipment. Strict management, excellence, design, manufacturing level continues to improve. In order to meet the needs of our customers, our latest developed belt filter press, sludge dewatering belt filter press, sludge filter press, the technology is leading  in China.

     

     


    发货照片 (5).jpg


    Meibang Environmental protection equipment co.,ltd.

    Office Add:Centre of  Building Minggao,No 123,Yingbing Road,Huadu Disctrict

    ,Guangzhou,Guangdong

    24 hours hotlineMiss Li  139 2623 5580  

    Factory Add:Meibang Industrial Park,No. 40 Dabu Road,Huadu Disctrict,Guangzhou,Guangdong

Follow Us
  • Mob./whatsapp/Wechat: +86 13926239002
  • E-mail: marketing@pressfiltercn.com
  • Tel.:+86 13926239002
  • Fax:+86 ( 020 ) 8969 1550
  • Add.:Room 1101-1111, 11th Floor, Mingo Center, 123 Yingbin Avenue, Huadu District, Guangzhou, Guangdong
Copyright © Guangdong Meibang Environmental Protection Equipment Co., LTD. All Rights Reserved